- Monday 8:00 AM - 5:00 PM
- Tuesday 8:00 AM - 5:00 PM
- Wednesday 8:00 AM - 5:00 PM
- Thursday 8:00 AM - 5:00 PM
- Friday 8:00 AM - 5:00 PM
- Saturday 8:00 AM - 12:00 PM
- Sunday Closed
CUTTING WIDTH (FT. IN. (M)) 10’ 4” (3.16) NUMBER OF DISCS 8 | |
FAST, SMOOTH CUTTINGThe maneuverable 9’2” (2.8 m) Discbine® 209 and the 10’4” (3.16 m) Discbine® 210 make high-quality hay with the smooth, trouble-free performance you expect from a genuine Discbine®. | |
CUT WITH EVEN MORE CONFIDENCEFor ultimate peace of mind, a 2-year base warranty is standard along with an additional year of the MowMax™ cutterbar warranty so you can cut with even more confidence. | |
STANDARD QUICKMAX™ KNIFE CHANGE SYSTEMThe QuickMax knife change system makes it easy to keep knives sharp for the close, clean cut you want and increased tonnage. | |
HIGH QUALITY AND FAST DRYDOWNChoose the best conditioning system for your crops – rubber chevron rolls, steel chevron rolls or LeaningEdge™ flail tines. |
SAVE TIME AND MOW BETTER WITH THE QUICKMAX™ KNIFE CHANGE SYSTEMWhen you use sharp knives, you get a smooth finish, add tons to your harvest and improve the cut quality of future cuttings. With the QuickMax system, a special knife tool allows you to change bent or dull knives in less time than getting out of the tractor, so you save time and crop. |
Cutting width (ft. in. (m)) |
10’ 4” (3.16) |
Cutterbar model |
MowMax™ Modular Cutterbar with ShockPRO™ hubs |
Number of discs |
8 |
Knives per disc |
2 |
Disc speed @ 540 rpm PTO speed (rpm) |
3000 |
Tilt angle (degrees) |
2° - 10° |
Flotation |
Up & back, adjustable springs |
Drive method |
PTO drive with slip & overrunning clutch to bevel gearbox to LH end of header, vertical PTO shaft to cutterbar |
Cutting height (in. (mm)) |
Flail Tine: 1.1-2.7 (29-68) or Roll: .95-2.4 (24-60) |
Cutting height w/optional high-stubble shoes (in. (mm)) |
2.25-4.5 (58-115) |
Cutting height w/optional adjustable shoes (in. (mm)) |
2.25-4.5 (58-115) |
Type |
Chevron intermeshing rubber or steel rolls |
Length / Diameter (in. (mm)) |
102 (2591) / 10.4 (264) |
Drive method |
4 HB V-belt and enclosed gears |
Speed (rpm) |
647 |
Conditioner roll tension adjustment |
Single crank |
Conditioner gap adjustment |
Adjustable drawbolt stop, each end |
Type |
Flail rotor with 100 tapered flails |
Length / Diameter (in. (mm)) |
102 (2591) / 22 (560) |
Drive method |
4 HB v-belt |
Speed (rpm) |
718 standard, 1000 optional |
Conditioner gap adjustment |
Single crank adjustable rotor hood |
Swath width (ft. (m)) |
7 (2.13) |
Windrow width (ft. (m)) |
3-7 (0.9-2.13) |
Input speed (rpm) |
540 or 1000 Standard Drawbar Attachment, 540 Only Swivel Hitch Attachment |
Driveline protection |
Slip clutch and overrunning clutch assembly at rear of PTO shaft |
Secondary driveline |
Double CV Driveline - Head repositionable under load |
Type |
Side-pull, curved tongue |
Hitch type |
Standard Drawbar with CV PTO, Swivel hitch with drawbar adapter or 2-point hitch |
Minimum PTO power required (hp (kW)) |
80 (60) |
Hydraulic circuits required |
2 |
Minimum relief pressure required (psi (bar)) |
1500 (103) |
Drawbar |
ASAE Category II |
Swivel Hitch - Drawbar |
ASAE Category II or III |
Swivel Hitch - 2-Point |
ASAE Category II, III-N, or III |
Electrical |
7-pin electrical connector for transport lights |
Tubeless ag rib implement tires |
Standard hitch and flail conditioner: 9.5L x 14 6PR/ Swivel hitch and roll conditioner: 11L x 15 6PR |
Max road speed (mph (kph)) |
20 (32) |
Width, transport (ft. in. (m)) |
11’ 3” (3.42) |
Width , operating (ft. in. (m)) |
16’ 0” (4.87) / 17’ 7’’ (5.36), with swivel hitch equipped |
Length, transport (ft. in. (m)) |
Flail Tine: 18’ 1’’ (5.50)*** or Roll: 17’ 7’’ (5.23)*** |
Length, operating (ft. in. (m)) |
Flail Tine: 17’ 8’’ (5.4)*** or Roll: 15’ 7’’ (4.75)*** |
Height (ft. in. (m)) |
Transport: 5’ 3” (1.60) / Operating: 4’ 5” (1.35) |
Ground clearance with head fully raised (in. (mm)) |
Flail Tine: 17 (4.32) or Roll: 18 (4.57) |
Operating weight (lbs. (kg)) |
Flail Tine: 4100 (1864)*** / Roll: 4160 (1891)*** |